100% Recycled Bottle and Cap




No. 500

We, Petainer Lidköping AB, confirm that the product:

PET Bottle Clear 100% Recycled PET (ECOCLEAR + CLEANPET)

fulfills the requirements on materials intended to come into contact with food as described in:

Regulation 1935/2004 / EC of 27.10.2004, Regulation 2023/2006 / EC of 22.12.2006, Regulation (EU) NO 10/2011 of 14.01.2011 with any subsequent reprints and amendments, Directive 97/48 / EC of 29.7. 1997.

Below information from our supplier of the raw material used in these products.

Resin in this product: 100% Recycled PET

The material is a PET polymer made from terephthalic acid (PTA), isophathalic acid (IPA) and monoethylene glycol (MEG).

Information on monomers for which restrictions are in place in Legislation EU 10/2011:

Terephthalic acid (PTA), CAS no 000100-21-0, SML 7.5 mg / Kg
Isophthalic acid (IPA) CAS no 000121-91-5, SML 5 mg / Kg 
Monoethylene glycol (MEG) CSA No. 000107-21-1, SML 30 mg / Kg
Diethylene glycol (DEG) 000111-46-6, SML 30 mg / Kg

Specific migration limits (SMLs) exist for the following additives: 

Antimony trioxide CAS no 0001 309-64-4, SML 0.04 mg / Kg
Cobalt, 0.05 mg / Kg
2-Aminobenzamide CAS No. 0000088-68-6, 0.05 mg / Kg

The use of additives and other raw materials for the manufacturing of this material complies with the requirements in EU 10/2011.

Specification on the use
This product is suitable for use in contact with dry, aqueous, acid and alcoholic up to 20% volume percent alcohol.

EN 1186-9: 2002 *: Test method for overall migration into aqueous food simulant by filling articles.
EN 1185-2009 *: The analysis of metals in food simulant was determined with ICP-AES. The migration were performed according to EN1186 (filling method).
EN 13130-XX: Determination of Primary Aromatic Amines (PAAs) in food simulants.

Detection by photometric screening method.
Specific migration of metals was determined by ICP-AES.

20% Ethanol, Test conditions 10 days, 40 C °
3% Acetic Acid, Test conditions 10 days, 40 ° C
3% Acetic Acid, Test conditions 10 days, 60 ° C

Conditions of contact with food
Testing for 10 days at 40 ° C shall cover any long term storage at room temperature or below, including heating up to 70 ° C for up to 2 hours, or heating up to 100 ° C for up to 15 minutes.
Ratio of the area of the food contact material to the used to determine the compliance of plastic food contact material: 9,4

Valid until: 1st of January 2021
Lidköping, 1st of January 2020 

Daniel Alexandersson
Quality Manager

To the best of our knowledge, the information contained herein is accurate as of the date of publication, however we do not assume any liability whatsoever for the accuracy and completeness of such information.
It is the responsibility of our customers to determine that their use of our product (s) is safe, lawful and technically suitable in their intended applications, for the protection of the environment, and for the health and safety of the employees and purchasers of the products. Because of possible changes in the law and in regulations, as well as possible changes in our products, we can not guarantee that the status of this product will remain unchanged. We, therefore, recommend that customers continuing to use this product verify its status periodically.
No liability can be accepted in respect of the use of Petainer’s products in conjunction with other materials. The information contained herein relates exclusively to our products when not used in conjunction with any third party materials.